NL1-ten Nylon Coupling, Nylon Sleeve, Gear Coupling, Gear Sleeve (3A2006)
 

Description: the polyurethane elastomeric is a new substance of polymer artificial in between rubber and plastic. It has both substantial strength of plastic and higher elasticity of rubber. Its traits are: 1, a wide assortment of hardness. It even now has rubber elongation and resilience at higher hardness. The polyurethane elastomeric has a hardness selection of Shore A10-D80. two. large strength. At rubber hardness, the tensile toughness, tear energy and load carrying capacity are a lot higher than common rubber content. At higher hardness, its impact strength and flexural strength are much higher than plastic substance. three, put on-resistant. Its wear resistance is quite exceptional, typically in the range of .01-.10cm³/1.61km, about three-5 occasions than rubber material. four, oil resistant. The polyurethane elastomeric is a very polar polymer compound which has lower affinity with non-polar mineral oil and is rarely eroded in gas oil and mechanical oil. 5, great resistance to oxygen and ozone. 6, outstanding vibration absorption overall performance, can do damping and buffering. In the mould production industry, it replaces rubber and springs.7, has good lower temperature performance. 8, radiation resistance. Polyurethane is highly resistant to higher power radiation and has satisfactory efficiency at ten-10 deg radiation dose. nine, with very good machining efficiency.

 

The polyurethane coupling, rubber coupling are produced by injection with high quality TPU materials or mould CSM/SBR. It is planning and special for all types of steel shaft coupling with quite great performance of high tensile energy, higher wear resistant, substantial elastic resilience, water resistant, oil resistant and outstanding fatigue resilience, large impact resistant etc. We have total sets injection moulds and offer entire assortment of GR, GS, MT, ML, MH, Hb, HRC, L, T, NM and Equipment J series couplings and so forth. with large high quality and excellent experience. Apply to all types of industrial metallic shaft coupling.

 

Requirements:

material: TPU, CSM/SBR, NBR, nylon and so forth.

coloration: yellow, red, purple, eco-friendly, black, beige etc.

area: easy

tensile power: eight-55Mpa

hardness: 70-98Shore A

elongation: four hundred%-650%

density: one.25g/cm³

elasticity impact: >25%

tear energy: 35-155KN/m

akron abrasion reduction:<0.05cm^three/one.61km

compression established (22h*70°C):<10%

operating temperature: 120°C

standard size for polyurethane coupling: 

GR14, GR19, GR24, GR28, GR38, GR42, GR48, GR55, GR65, GR75, GR90, GR100, GR110, GR125, GR140, GR160, GR180

GS14, GS19, GS24, GS28, GS38, GS42, GS48, GS55, GS65, GS75, GS90, GS100, GS110, GS125, GS140, GS160, GS180

MT1, MT2, MT3, MT4, MT5, MT6, MT7, MT8, MT9, MT10, MT11, MT12, MT13

ML1, ML2, ML3, ML4, ML5, ML6, ML7, ML8, ML9, ML10, ML11, ML12, ML13

MH45, MH55, MH65, MH80, MH90, MH115, MH130, MH145, MH175, MH200

HRC70, HRC90, HRC110, HRC130, HRC150, HRC180, HRC230, HRC280

L35, L50, L70, L75, L90/ninety five, L99/one hundred, L110, L150, L190, L225, L276

FALK-R 10R, 20R, 30R, 40R, 50R, 60R, 70R, 80R

SBT T40, T45, T50, T55, T60, T65, T70, T75, T80, T85, T90, T95, T100, T105, T108, T110, T115, T120, T125, T130, T135, T140, T145, T150, T154, T170, T185, T190, T210

Joong Ang CR0050, 0070, 571, 571, 2035, 2035A, 3545, 4560, 6070, 7080

MS571, MS571, MS1119, MS1424, MS1928, MS1938, MS2845, MS3860, MS4275, MS6510

D14, D14L, D20, D25, D30, D30L, D35, D40, D45, D49, D55, D65

5H, 6H, 7H, 8H, 9H, 10H, 11H

 

standard measurement for rubber coupling:

Hb80, Hb95, Hb110, Hb125, Hb140, Hb160, Hb180, Hb200, Hb240, Hb280, Hb315

HRC70, HRC90, HRC110, HRC130, HRC150, HRC180, HRC230, HRC280

L35, L50, L70, L75, L90/ninety five, L99/100, L110, L150, L190, L225

NM50, NM67, NM82, NM97, NM112, NM128, NM148, NM168, NM194, NM214, NM240, NM265

NOR-MEX168-ten, NOR-MEX194-ten, NOR-MEX214-ten, NOR-MEX240-10, NOR-MEX265-ten

FCL1#, FCL2#, FCL3#, FCL4#, FCL5#, FCL6#, FCL7#, FCL8#

FCL90, FCL100, FCL112, FCL125, FCL140, FCL160, FCL180, FCL200, FCL224, FCL250, FCL280, FCL315, FCL335, FCL400, FCL450, FCL560, FCL630

Gear 3J, 4J, 5J, 6J, 7J, 8J, 9J, 10J, 11J, 12J, 13J, 14J

Hytre 4H, 5H, 6H, 7H, 8H, 9H, 11H

Tyre F40, F50, F60, F70, F80, F90, F100, F110, F120, F140, F160 

SBT T75, T80, T85, T90, T95, T100, T105, T108, T110, T115, T120, T125, T130, T135, T140, T145, T150, T154, T170, T210

FCLpin #one, #two, #3, #four, #5, #six, #8

GR42, GR48, GR55, GR65, GR75

 

common dimensions for nylon coupling:

NL1, NL2, NL3, NL4, NL5, NL6, NL7, NL8, NL9, NL10

M28, M32, M38, M42, M48, M58, M65

packing in cartons

OEM & CZPT dimension are agreed

particular provide all sorts of metal coupling for FCL, NM, MH, HRC, Adore Joy, Joongang, Centafelx, XL-GR, Tyre

***when you enquiry, pls confirm variety, measurement amount and quantity***